Combination instrument
Activation and test
Day night mode
Warning Notes
Indicator lamps


Display

1. Speed
1. Shift warning light : The shift warning light is integrated in the tachometer display.
2. Gear display
3. Unit for the speed display
4. Speed
5. Unit for the speedometer
6. ODO Display
7. Coolant temperature indicator
8. Fuel level display
9. Bluetooth
10.(Optional) Time
11. SET - Only shown where the menu overview is closed
12. Favourites display
13. ABS Mode (MY 19 onwards)
Speed

Shift warning light

Info In sixth-gear, the shift warning light is deactivated when the engine is warm after the first service.
Coolant temperature | ≤ 35 °C |
ODO | < 1,000 km |
The shift warning light always lights up at | 6500 rpm |
Coolant temperature | > 35 °C |
ODO | > 1,000 km |
RPM1 shift warning light | lights up |
RPM2 shift warning light | flashes |
Speed

ODO Display

Info This value is retained, even if the battery is disconnected from the vehicle or the fuse blows
Coolant temperature indicator

Info When all bars light up, the following warning note ENGINE TEMP HIGH appear
Possible states- The engine is cold – Up to three bars light up.
- Engine warm – Four to five bars light up.
- Engine hot – Six to eight bars light up.
- Engine very hot – All eight bars light up red.
Fuel level Display

Info If the fuel level is getting low, the last segment flashes red and the following warning note also appears LOW FUEL. The fuel level is displayed with a slight delay to prevent the indicator from con- stantly moving while riding. The fuel level display is not updated while the side stand is folded out or the emer- gency off switch is switched off. Once the side stand is folded up and emergency OFF switch is switched on, the fuel level display is next updated after 2 minutes. The fuel level display flashes if the combination instrument does not receive a signal from the fuel level sensor.
Time

Info The time must be reset after the battery was disconnected or the fuse was removed.
Favourites display

Info One to four items of information selected are displayed on two lines. Five to eight items of information selected are displayed on a single line.
Quick Selector 1 display

Info The Quick Selector 1 can be configured in the Quick Selector 1 menu. Any informa- tion can be selected.
Quick Selector 1 display

Info The Quick Selector 1 can be configured in the Quick Selector 1 menu. Any informa- tion can be selected.
Menu

Info Press the SET button 1 in the standard display to open the menu. Navigate through the menu using the UP button 2 or the DOWN button 3. Press the BACK button 4 to close the current menu or the menu overview.
KTM MY RIDE (optional)

The motorcycle is stationary.
- Function KTM MY RIDE activated (optional).
- Function Bluetooth® activated.
- Press the SET button when the menu is closed.
- Press the UP> or DOWN button until KTM MY RIDE is marked. Press the SET button to open the menu.
Info
Not every cellphone is suitable for pairing with the combination instrument. The standard Bluetooth® 2.1 must be supported.
KTM my ride app is required for android phones in MY17/ MY18 vehicles.
- It is not recommended to operat0e handle bar switches to perform audio functions of mobile while vehicle is in motion. Also, law does not permit talking over mobile phone while driving the vehicle. This may lead to fatal accident and breach of Motor Vehicle Act & Rules. - It is highly recommended to respond to mobile call and operate handle bar knobs for performing audio functions of mobile only while vehicle is in standstill condition.
Info

- Press the SET button when the menu is closed.
- Press the UP or DOWN button until Info is marked.Press SET button to open the menu
General information can be accessed in Info.
Motorcycle

- Press the SET button when the menu is closed.
- Press the UP or DOWN button until Motorcycle is marked. Press the SET button to open the menu
The vehicle drive mode can be configured in Motorcycle.
Settings

- The motorcycle is stationary
- Press the SET button when the menu is closed.
- Press the UP or DOWN button until Settings is marked. Press the SET button to open the menu.
Preferences

- Press the SET button when the menu is closed.
- Press the UP or DOWN button until Settings is marked. Press the SET button to open the menu
Caution
Speedometer on your Duke 390 vehicle is equipped with Bluetooth® wireless technology. Watching or operating speedometer for selection of any program is not recommended while vehicle is in motion, as such acts are breach of Motor Vehicles Act & Rules. Also it may lead to penalty under the aforesaid law & can cause road accident. Make speedometer setting selections only while vehicle is in standstill condition
Caution for operating bluetooth technology
Pairing(optional)

- Function KTM MY RIDE activated (optional).
- Function Bluetooth® activated.
- The Bluetooth® function should also be activated in the device to be paired.
- Press the SET button when the menu is closed.
- Press the UP or DOWN button until KTM MY RIDE is marked. Press the SET button to open the menu.
- Press the UP or DOWN button until Pairing is marked. Press the SET button to open the menu.
- Press the UP or DOWN button until Pairing is marked. Press the SET button to pair a suitable with the combination instrument via Bluetooth®.
- Confirmation of the Passkey successfully completes the pairing
Info When a suitable cellphone has been successfully paired, the name of the paired cellphone is displayed.Press the UP or DOWN button until paired device is marked on the display. The paired device can be deleted by pressing the SET button. The device most recently linked is automatically paired with the combination instrument when Bluetooth® is switched on and as soon as this device is in range and has not been previously deleted. Not every cellphone is suitable for pairing with the combination instrument.
Caution It is not recommended to operate handle bar switches to perform audio functions of mobile while vehicle is in motion. Also, law does not permit talking over mobile phone while driving the vehicle. This may lead to fatal accident and breach of Motor Vehicle Act & Rules. It is highly recommended to respond to mobile call and operate handle bar knobs for performing audio functions of mobile only while vehicle is in standstill condition
Audio(optional)

- Function Bluetooth® activated.
- The Bluetooth® function should also be activated in the device to be paired
- Press the SET button when the menu is closed.
- Press the UP /DOWN button until KTM MY RIDE is marked. Press SET button to open the menu
Info The audio function can be added to Quick Selector 1 or Quick Selector 2 for easier operation
Warning Danger of accidents Headphone volume which is too high distracts attention from traffic activity. Always select headphone volume which is low enough for you to still clearly hear acoustic signals.
- .
- Press the UP or DOWN button until Audio is marked. Press the SET button to open the menu.
- Press and hold the UP button to increase the audio volume.
- Press and hold the DOWN button to reduce the audio volume.
- Press the UP button briefly to change to the next audio track.
- Press the DOWN button briefly to change to the previous audio track.
- Press the SET button to play or pause the audio track.
Caution It is not recommended to operate handle bar switches to perform audio functions of mobile while vehicle is in motion. Also, law does not permit talking over mobile phone while driving the vehicle. This may lead to fatal accident and breach of Motor Vehicle Act & Rules. It is highly recommended to respond to mobile call and operate handle bar knobs for performing audio functions of mobile only while vehicle is in standstill condition.
Telephony (optional)

- Function Bluetooth® activated.
- The Bluetooth® function should also be activated in the device to be paired
- Headset linked with appropriate cellphone.
Warning Danger of Accidents Headphone volume which is too high distracts attention from traffic activity. – Always select headphone volume which is low enough for you to still clearly hear acoustic signals.
Info The call duration and contact are displayed. Depending on the cellphone settings, the contact is shown by name.
Caution - It is not recommended to operate handle bar switches to perform audio functions of mobile while vehicle is in motion. Also, law does not permit talking over mobile phone while driving the vehicle. This may lead to fatal accident and breach of Motor Vehicle Act & Rules. - It is highly recommended to respond to mobile call and operate handle bar knobs for performing audio functions of mobile only while vehicle is in standstill condition.
General Info

- Press the SET button when the menu is closed.
- Press the UP or DOWN button until Info is marked. Press the SET button to open the menu.
- Press the UP or DOWN button until General Info is marked.Press the SET button to open the menu.
Trip 1

- Press the SET button when the menu is closed.
- Press the UP or DOWN button until Info is marked. Press the SET button to open the menu.
- Press the UP or DOWN button until Trip 1 is marked. Press the SET button to open the menu.
Trip 1 shows the distance since the last reset, such as between two refueling stops. Trip 1 is running and counts up to 9999.
ØCons1 indicates the average fuel consumption based on Trip 1.
ØSpeed1 indicates the average speed based on Trip 1 and Trip Time1
Trip Time1 shows the journey time on the basis of Trip 1 and runs as soon as a speed signal is received.
Fuel Range indicates the possible distance you can cover with the fuel reserve.
Press and hold the SETbutton for 3-5 seconds | All entries in the Trip 1 menu are reset |
Trip 2

- Press the SET button when the menu is closed.
- Press the UP or DOWN button until Info is marked. Press the SET button to open the menu.
- Press the UP or DOWN button until Trip 2 is marked. Press the SET button to open the menu.
Trip 2 shows the distance since the last reset, such as between two refueling stops. Trip 2 is running and counts up to 9999.
ØCons indicates the average fuel consumption based on Trip 2.
Øspeed2 indicates the average speed based on Trip 2 and Trip Time2. Trip Time2 shows the journey time on the basis of Trip 2 and runs as soon as a speed signal is received.
Fuel Range indicates the possible distance you can cover with the fuel reserve.
Press and hold the SETbutton for 3-5 seconds | All entries in the Trip 2 menu are reset |
Warning

- Press the SET button when the menu is closed.
- Press the UP or DOWN button until Info is marked. Press the SET button to open the menu.
- Press the UP or DOWN button until Trip 2 is marked. Press the SET button to open the menu.
- Use the UP or DOWN button to navigate through the warnings.
ABS

- Press the SET button when the menu is closed.
- Press the UP or DOWN button until Motorcycle is marked. Press the SET button to open the menu.
Warning - Voiding of the government approval for road use and the insurance coverage If the ABS is switched off completely, the vehicle's approval for road use is invali- dated. – Only operate the vehicle in closed-off areas remote from public road traffic if the ABS is switched off completely. – Press the UP or DOWN button until ABS is marked. Press the SET button to open the menu. – Activate the menu item using the UP or DOWN button. Press the ABS button to switch off SET or to select between ABS modes.
Info The ABS can only be reactivated by switching on the ignition again. When the Road ABS mode is enabled, ABS controls both wheels.When the Sup Mot ABS mode is enabled, ABS only controls the front wheel. The rear wheel is not controlled by ABS and may lock during braking maneuvers.
Favourites

- Press the SET button when the menu is closed.
- Press the UP or DOWN button until Settings is marked. Press the SET button to open the menu.
- Press the UP or DOWN button until Favourites is marked. Press the SET button to open the menu.
- Use the UP or DOWN button to Press the UP or DOWN button to activate the menu item and select it with the SET button.
Quick Selector 1

- Press the SET button when the menu is closed.
- Press the UP or DOWN button until Settings is marked. Press the SET button to open the menu.
- Press the UP or DOWN button until Quick Selector 1 is marked. Press the SET button to open the menu.
- Use the UP or DOWN button to Press the UP or DOWN button to activate the menu item and select it with the SET button.
Quick Selector 2

- Press the SET button when the menu is closed.
- Press the UP or DOWN button until Settings is marked. Press the SET button to open the menu.
- Press the UP or DOWN button until Quick Selector 2 is marked. Press the SET button to open the menu.
- Use the UP or DOWN button to Press the UP or DOWN button to activate the menu item and select it with the SET button.
Bluetooth

- Press the SET button when the menu is closed.
- Press the UP or DOWN button until Preferences is marked. Press the SET button to open the menu.
- Press the UP or DOWN button until Bluetooth is marked. Press the SET button to open the menu.
- Activate the menu using the UP or DOWN button.
- Press the SET button to switch the Bluetooth® function on or off
Info The Bluetooth® function can only be used in conjunction with KTM MY RIDE(optional). When the Bluetooth® function is switched on, the Bluetooth® symbol appears in the display of the combination instrument.
Caution - It is not recommended to operate handle bar switches to perform audio functions of mobile while vehicle is in motion. Also, law does not permit talking over mobile phone while driving the vehicle. This may lead to fatal accident and breach of Motor Vehicle Act & Rules. - It is highly recommended to respond to mobile call and operate handle bar knobs for performing audio functions of mobile only while vehicle is in standstill condition
Shift Light

- The motorcycle is stationary.
- ODO > 1000 km
- Press the SET button when the menu is closed.
- Press the UP or DOWN button until Preferences is marked. Press the SET button to open the menu.
- Press the UP or DOWN button until Shift Light is marked. Press the SET button to open the menu.
- Activate the menu item using the UP or DOWN button.
- Press the SET button to switch the shift warning light on or off and to adjust the engine speed for the gear shift recommendation.
Info When the engine speed reaches RPM 1, the speed display lights up red. When the engine speed reaches RPM 2, the speed display flashes red.
Setting the time and date.

-
The motorcycle is stationary.
- Press the SET button when the menu is closed.
- Press the UP or DOWN button until Preferences is marked. Press the SET button to open the menu.
- Press the UP or DOWN button until Clock/Date is marked. Press the SET button to open the menu.
Setting the time and date.

- Press the UP or DOWN button until time is marked.
- Press the SET button The hour flashes and is underlined.
- Press the UP or DOWN button until the current hour is set
- Press the SET button. The minutes flash and are underlined.
- Press the UP or DOWN button until the current minute is set
- Press the SET button. The time is stored.

- Press the UP or DOWN button until time is marked.
- Press the SET button The day flashes and is underlined.
- Press the UP or DOWN button until the current day is set
- Press the SET button. The month flashes and are underlined.
- Press the UP or DOWN button until the current month is set
- Press the SET button. The year flashes and is underlined.
- Press the UP or DOWN button until the current year is set
- Press the SETbutton
DRL

- Press the SET button when the menu is closed.
- Press the UP or DOWN button until Preferences is marked. Press the SET button to open the menu.
Warning: Danger of accidents When visibility is poor, the daytime running light is not a substitute for the low beam. Automatic switching between the daytime running light and low beam may only be partially available when visibility is significantly impaired due to fog, snow or rain. - Ensure that the appropriate type of lighting is always selected. - If necessary switch off the daytime running lights using the menu before going on a ride or when stopped so that the low beam is switched on permanently. - Note the legal regulations regarding the daytime running light. - Press the UP or DOWN button until DRL is marked. Press the SET button to open the menu. - Activate the menu item using the UP or DOWN button . - Press the SET button to switch the daytime running light on or off.
Distance

- Press the SET button when the menu is closed.
- Press the UP or DOWN button until Preferences is marked. Press the SET button to open the menu.
- Press the UP or DOWN button until Units is marked. Press the SET button to open the menu.
- Press the UP or DOWN button until Distance is marked. Press the SET button to open the menu.
- Activate the menu item using the UP or DOWN button.
- Press the SET button to confirm the desired unit.
Temp

- Press the SET button when the menu is closed.
- Press the UP or DOWN button until Preferences is marked. Press the SET button to open the menu.
- Press the UP or DOWN button until Units is marked. Press the SET button to open the menu.
- Press the UP or DOWN button until Temp is marked. Press the SET button to open the menu.
- Activate the menu item using the UP or DOWN button.
- Press the SET button to confirm the desired unit.
Fuel Cons

- Press the SET button when the menu is closed.
- Press the UP or DOWN button until Preferences is marked. Press the SET button to open the menu.
- Press the UP or DOWN button until Units is marked. Press the SET button to open the menu.
- Press the UP or DOWN button until Fuel Cons is marked. Press the SET button to open the menu.
- Activate the menu item using the UP or DOWN button.
- Press the SET button to confirm the desired unit.
Language

- Press the SET button when the menu is closed.
- Press the UP or DOWN button until Preferences is marked. Press the SET button to open the menu.
- Press the UP or DOWN button until Units is marked. Press the SET button to open the menu.
- Press the UP or DOWN button to activate the menu item and select it with the SET button.
Service

- Press the SET button when the menu is closed.
- Press the UP or DOWN button until Preferences is marked. Press the SET button to open the menu.
- Press the UP or DOWN button until Service is marked. Press the SET button to open the menu.
Extra Functions

- Motorcycle with optional supplementary function.
- Press the SET button when the menu is closed.
- Press the UP or DOWN button until Preferences is marked. Press the SET button to open the menu.
- Press the UP or DOWN button until Extra Functions is marked. Press the SET button to open the menu.
- Use the UP or DOWN button to navigate through the extra functions.
Info The current KTM PowerParts and the available software for your vehicle can be found on the KTM website.
Condensation inside TFT meter is a natural phenomenon
Condensation occurs when atmospheric air containing water vapor or humidity enters the TFT meter due to temperature difference. A thin film of fog can form on the inside surface of the TFT meter. The thin fog will clear and exit through during normal operating condition.
Condensation & fogging may happen during rain or after washing.
Moisture condensation inside the headlamp lens will disappear gradually by driving the vehicle. Time for evaporation will vary depending on the humidity of the ambient air.
Note:- If condensation inside the TFT does not evaporate and meter is not legible then bring the vehicle to KTM Authorised Dealer for inspection.